~nabeken/diary/

Gentoo Linux(6年くらい)とFreeBSD(1年くらい)とOpenBSD(新参者)を使う日々。


IHANet BGP peering overview

DELL Power Edge T105 に Gentoo Linux をインストールする

Posted on Mon Sep 22 19:45:26 +0900 2008 by nabeken

メモリが 4GB 以上あると、DVD-ROM (sata_nv) が認識されないようです。その場合、kernel のブートパラメータに

 # gentoo mem=2048MB

を渡すと起動しました。(参考: http://lists.us.dell.com/pipermail/linux-poweredge/2008-July/036795.html )

いろいろ

 # hdparm -t /dev/sd[ab]

/dev/sda:
 Timing buffered disk reads:  176 MB in  3.03 seconds =  58.02 MB/sec

 /dev/sdb:
 Timing buffered disk reads:  174 MB in  3.00 seconds =  57.91 MB/sec

/dev/sdを raid0, sd[ab2 を raid1 + LVM で運用します。

 # hdparm -t /dev/md1

/dev/md1:
 Timing buffered disk reads:  348 MB in  3.00 seconds = 115.88 MB/sec

上々ですね。

インストール後は正常に動作しています。

 # uname -a
Linux nagisa.tokyo.tknetworks.org 2.6.26-gentoo-r1 #2 SMP PREEMPT Mon Sep 22 18:28:34 Local time zone must be set-- x86_64 Dual-Core AMD Opteron(tm) Processor 1212 AuthenticAMD GNU/Linux

 # dmesg
Initializing cgroup subsys cpuset
Linux version 2.6.26-gentoo-r1 (root@livecd) (gcc version 4.1.2 (Gentoo 4.1.2 p1.1)) #2 SMP PREEMPT Mon Sep 22 18:28:34 Local time zone must be set--
Command line: root=/dev/ram0 dolvm dolvm2 lvmraid=/dev/md1 real_root=/dev/raid0/root
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
 BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ca000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
 BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved)
 BIOS-e820: 0000000080000000 - 00000000cfee0000 (usable)
 BIOS-e820: 00000000cfee0000 - 00000000cfef2000 (ACPI data)
 BIOS-e820: 00000000cfef2000 - 00000000cff7f000 (ACPI NVS)
 BIOS-e820: 00000000cff80000 - 00000000d0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
Entering add_active_range(0, 256, 524272) 1 entries of 3200 used
Entering add_active_range(0, 524288, 851680) 2 entries of 3200 used
Entering add_active_range(0, 1048576, 1245184) 3 entries of 3200 used
max_pfn_mapped = 1245184
init_memory_mapping
DMI present.
ACPI: RSDP 000F79B0, 0024 (r2 PTLTD )
ACPI: XSDT CFEEDFFB, 009C (r1 DELL   PE_SC3    6040000 DELL        0)
ACPI: FACP CFEF1507, 00F4 (r3 DELL   PE_SC3    6040000 DELL    F4240)
ACPI: DSDT CFEEE097, 33FC (r1 DELL   PE_SC3    6040000 MSFT  100000E)
ACPI: FACS CFEF2FC0, 0040
ACPI: TCPA CFEF15FB, 0032 (r1 Phoeni  x        6040000  TL         0)
ACPI: SLIC CFEF162D, 0024 (r1 DELL   PE_SC3    6040000 PTL         1)
ACPI: SPCR CFEF1651, 0050 (r1 DELL   PE_SC3    6040000 PTL         1)
ACPI: EINJ CFEF16A1, 01B0 (r1 PTL    WHEAPTL   6040000 PTL         1)
ACPI: HEST CFEF1851, 00A8 (r1 PTL    WHEAPTL   6040000 PTL         1)
ACPI: BERT CFEF18F9, 0030 (r1 PTL    WHEAPTL   6040000 PTL         1)
ACPI: SSDT CFEF1929, 00E1 (r1 wheaos  wheaosc  6040000 INTL 20050624)
ACPI: ERST CFEF1A0A, 0270 (r1 PTL    WHEAPTL   6040000 PTL         1)
ACPI: SRAT CFEF1C7A, 00C8 (r1 AMD    HAMMER    6040000 AMD         1)
ACPI: SSDT CFEF1D42, 01C4 (r1 AMD    POWERNOW  6040000 AMD         1)
ACPI: MCFG CFEF1F06, 003C (r1 PTLTD    MCFG    6040000  LTP        0)
ACPI: HPET CFEF1F42, 0038 (r1 PTLTD  HPETTBL   6040000  LTP        1)
ACPI: APIC CFEF1F7A, 005E (r1 PTLTD  	 APIC    6040000  LTP        0)
ACPI: BOOT CFEF1FD8, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: Node 0 PXM 0 0-a0000
Entering add_active_range(0, 0, 157) 0 entries of 3200 used
SRAT: Node 0 PXM 0 100000-d0000000
Entering add_active_range(0, 256, 524272) 1 entries of 3200 used
Entering add_active_range(0, 524288, 851680) 2 entries of 3200 used
SRAT: Node 0 PXM 0 100000000-130000000
Entering add_active_range(0, 1048576, 1245184) 3 entries of 3200 used
NUMA: Allocated memnodemap from e000 - 10640
NUMA: Using 20 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000130000000
  NODE_DATA [0000000000001000 - 0000000000004fff]
  bootmap [0000000000011000 -  0000000000036fff] pages 26
  early res: 0 [0-fff] BIOS data page
  early res: 1 [6000-7fff] TRAMPOLINE
  early res: 2 [200000-8ab0d7] TEXT DATA BSS
  early res: 3 [36fb2000-37fef8bf] RAMDISK
  early res: 4 [9dc00-fffff] BIOS reserved
  early res: 5 [8000-dfff] PGTABLE
  early res: 6 [e000-1063f] MEMNODEMAP
 [ffffe20000000000-ffffe20002dfffff] PMD -> [ffff810001200000-ffff810003ffffff] on node 0
 [ffffe20003800000-ffffe200043fffff] PMD -> [ffff81000c000000-ffff81000cbfffff] on node 0
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1245184
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
    0:        0 ->      157
    0:      256 ->   524272
    0:   524288 ->   851680
    0:  1048576 ->  1245184
On node 0 totalpages: 1048173
  DMA zone: 56 pages used for memmap
  DMA zone: 1818 pages reserved
  DMA zone: 2123 pages, LIFO batch:0
  DMA32 zone: 14280 pages used for memmap
  DMA32 zone: 833288 pages, LIFO batch:31
  Normal zone: 2688 pages used for memmap
  Normal zone: 193920 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000ca000
PM: Registered nosave memory: 00000000000ca000 - 0000000000100000
PM: Registered nosave memory: 000000007fff0000 - 0000000080000000
PM: Registered nosave memory: 00000000cfee0000 - 00000000cfef2000
PM: Registered nosave memory: 00000000cfef2000 - 00000000cff7f000
PM: Registered nosave memory: 00000000cff7f000 - 00000000cff80000
PM: Registered nosave memory: 00000000cff80000 - 00000000d0000000
PM: Registered nosave memory: 00000000d0000000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
PM: Registered nosave memory: 00000000fec10000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000fff80000
PM: Registered nosave memory: 00000000fff80000 - 0000000100000000
Allocating PCI resources starting at d1000000 (gap: d0000000:10000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 36016 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 2
Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1029331
Policy zone: Normal
Kernel command line: root=/dev/ram0 dolvm dolvm2 lvmraid=/dev/md1 real_root=/dev/raid0/root
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2009.258 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
Node 0: aperture @ 4000000 size 32 MB
Aperture pointing to e820 RAM. Ignoring.
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
PM: Registered nosave memory: 0000000004000000 - 0000000008000000
Memory: 4043940k/4980736k available (4200k kernel code, 148752k reserved, 1239k data, 384k init)
CPA: page pool initialized 1 of 1 pages preallocated
hpet clockevent registered
Calibrating delay using timer specific routine.. 4020.40 BogoMIPS (lpj=2010204)
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
ACPI: Core revision 20080321
CPU0: Dual-Core AMD Opteron(tm) Processor 1212 stepping 03
Using local APIC timer interrupts.
APIC timer calibration result 12557894
Detected 12.557 MHz APIC timer.
Booting processor 1/1 ip 6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4018.34 BogoMIPS (lpj=2009172)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Dual-Core AMD Opteron(tm) Processor 1212 stepping 03
Brought up 2 CPUs
Total of 2 processors activated (8038.75 BogoMIPS).
net_namespace: 1208 bytes
xor: automatically using best checksumming function: generic_sse
   generic_sse:  5996.000 MB/sec
xor: using function: generic_sse (5996.000 MB/sec)
NET: Registered protocol family 16
No dock devices found.
node 0 link 0: io port [1000, 3fff]
node 0 link 0: io port [4000, fffff]
TOM: 00000000d0000000 aka 3328M
node 0 link 0: mmio [d0000000, d04fffff]
node 0 link 0: mmio [fed00000, fed0ffff]
node 0 link 0: mmio [d8000000, dfffffff]
node 0 link 0: mmio [fec00000, fec0ffff]
node 0 link 0: mmio [e0000000, efffffff]
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [f0000000, fe0bffff]
TOM2: 0000000130000000 aka 4864M
bus: [00,ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [d0000000, d7ffffff]
bus: 00 index 2 mmio: [fec10000, ffffffff]
bus: 00 index 3 mmio: [d8000000, febfffff]
bus: 00 index 4 mmio: [fec00000, fec0ffff]
bus: 00 index 5 mmio: [a0000, bffff]
bus: 00 index 6 mmio: [130000000, fcffffffff]
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 4
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - e04fffff
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.XVR0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.XVR2._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.XVR3._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [LSI1] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
DMAR:parse DMAR table failure.
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 4000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
ACPI: RTC can wake from S4
system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:00: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:00: iomem range 0xfed00000-0xfed00fff has been reserved
system 00:02: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:03: ioport range 0x8000-0x807f has been reserved
system 00:03: ioport range 0x8080-0x80ff has been reserved
system 00:03: ioport range 0x8400-0x847f has been reserved
system 00:03: ioport range 0x8480-0x84ff has been reserved
system 00:03: ioport range 0x8800-0x887f has been reserved
system 00:03: ioport range 0x8880-0x88ff has been reserved
system 00:03: ioport range 0x2040-0x207f has been reserved
system 00:03: ioport range 0x2000-0x203f has been reserved
system 00:05: ioport range 0x4d0-0x4d1 has been reserved
system 00:0a: ioport range 0xc00-0xc7f has been reserved
PCI: Bridge: 0000:00:09.0
  IO window: 3000-3fff
  MEM window: 0xd0100000-0xd01fffff
  PREFETCH window: 0x00000000d8000000-0x00000000dfffffff
PCI: Bridge: 0000:00:0b.0
  IO window: disabled.
  MEM window: 0xd0200000-0xd02fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 16630k freed
Simple Boot Flag at 0x62 set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1222109183.572:1): initialized
squashfs: version 3.3 (2007/10/31) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.5.0
ocfs2: Registered cluster interface o2cb
OCFS2 Node Manager 1.5.0
OCFS2 DLM 1.5.0
OCFS2 DLMFS 1.5.0
OCFS2 User DLM kernel interface loaded
GFS2 (built Sep 22 2008 18:01:52) installed
Lock_Nolock (built Sep 22 2008 18:02:02) installed
msgmni has been set to 7930
async_tx: api initialized (sync-only)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
pci 0000:00:00.0: Enabling HT MSI Mapping
pci 0000:00:07.0: Enabling HT MSI Mapping
pci 0000:00:08.0: Enabling HT MSI Mapping
pci 0000:00:0b.0: Enabling HT MSI Mapping
pci 0000:00:0b.0: Found enabled HT MSI Mapping
pci 0000:00:0b.0: Linking AER extended capability
pci 0000:00:0c.0: Enabling HT MSI Mapping
pci 0000:00:0c.0: Found enabled HT MSI Mapping
pci 0000:00:0c.0: Linking AER extended capability
pci 0000:00:0d.0: Enabling HT MSI Mapping
pci 0000:00:0d.0: Found enabled HT MSI Mapping
pci 0000:00:0d.0: Linking AER extended capability
pci 0000:00:0e.0: Enabling HT MSI Mapping
pci 0000:00:0e.0: Found enabled HT MSI Mapping
pci 0000:00:0e.0: Linking AER extended capability
pci 0000:01:08.0: Boot video device
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie01]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie01]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie01]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie01]
Allocate Port Service[0000:00:0e.0:pcie03]
AER service couldn't init device 0000:00:0b.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0c.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0d.0:pcie01 - no _OSC support
AER service couldn't init device 0000:00:0e.0:pcie01 - no _OSC support
Linux agpgart interface v0.103
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int64x1   1808 MB/s
raid6: int64x2   2187 MB/s
raid6: int64x4   2066 MB/s
raid6: int64x8   1500 MB/s
raid6: sse2x1    2777 MB/s
raid6: sse2x2    3691 MB/s
raid6: sse2x4    3804 MB/s
raid6: using algorithm sse2x4 (3804 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
registered taskstats version 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 384k freed
sata_nv 0000:00:07.0: version 3.5
sata_nv 0000:00:07.0: enabling device (0005 -> 0007)
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:07.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x20f0 ctl 0x20e0 bmdma 0x20b0 irq 23
ata2: SATA max UDMA/133 cmd 0x20d0 ctl 0x20c0 bmdma 0x20b8 irq 23
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: WDC WD800AAJS-18TDA1, 01.00A04, max UDMA/133
ata1.00: 156250000 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: WDC WD800AAJS-70TDA1, 01.00A03, max UDMA/100
ata2.00: 156301488 sectors, multi 16: LBA48 
ata2.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      WDC WD800AAJS-18 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156250000 512-byte hardware sectors (80000 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156250000 512-byte hardware sectors (80000 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: Direct-Access     ATA      WDC WD800AAJS-70 01.0 PQ: 0 ANSI: 5
sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2
sd 1:0:0:0: [sdb] Attached SCSI disk
ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:08.0 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x2440 ctl 0x2430 bmdma 0x2400 irq 22
ata4: SATA max UDMA/133 cmd 0x2420 ctl 0x2410 bmdma 0x2408 irq 22
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: HL-DT-STDVD-ROM GDRH20N, 0D08, max UDMA/100
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: CD-ROM            HL-DT-ST DVD-ROM GDRH20N  0D08 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sr 2:0:0:0: Attached scsi generic sg2 type 5
scsi:  Detection failed (no card)
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
Adaptec aacraid driver 1.1-5[2456]-ms
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
QLogic Fibre Channel HBA Driver: 8.02.01-k4
Emulex LightPulse Fibre Channel SCSI driver 8.2.6
Copyright(c) 2004-2008 Emulex.  All rights reserved.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 21, io mem 0xd0001000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 20, io mem 0xd0000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usb 2-5: new low speed USB device using ohci_hcd and address 2
usb 2-5: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input:   USB Keyboard as /class/input/input0
input,hidraw0: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:02.0-5
input:   USB Keyboard as /class/input/input1
input,hidraw1: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:02.0-5
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
tg3.c:v3.92.1 (June 9, 2008)
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNK2] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Tigon3 [partno(BCM95722) rev a200 PHY(5722/5756)] (PCI Express) 10/100/1000Base-T Ethernet 00:22:19:08:60:a0
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
md: Autodetecting RAID arrays.
md: Scanned 4 and added 4 devices.
md: autorun ...
md: considering sdb2 ...
md:  adding sdb2 ...
md: sdb1 has different UUID to sdb2
md:  adding sda2 ...
md: sda1 has different UUID to sdb2
md: created md1
md: bind
md: bind
md: running: 
md1: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdb2
raid0:   comparing sdb2(77931200) with sdb2(77931200)
raid0:   END
raid0:   ==> UNIQUE
raid0: 1 zones
raid0: looking at sda2
raid0:   comparing sda2(77931200) with sdb2(77931200)
raid0:   EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 155862400 blocks.
raid0 : conf->hash_spacing is 155862400 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: considering sdb1 ...
md:  adding sdb1 ...
md:  adding sda1 ...
md: created md0
md: bind
md: bind
md: running: 
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
ReiserFS: dm-0: found reiserfs format "3.6" with standard journal
ReiserFS: dm-0: using ordered data mode
ReiserFS: dm-0: journal params: device dm-0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: dm-0: checking transaction log (dm-0)
ReiserFS: dm-0: Using r5 hash to sort names
dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [C000] (supports 2 throttling states)
ACPI: ACPI0007:01 is registered as cooling_device1
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2040
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2000
input: PC Speaker as /class/input/input4
Adding 1023992k swap on /SWAP.IMG.  Priority:-1 extents:372 across:1864272k
ADDRCONF(NETDEV_UP): eth0: link is not ready
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready